Intelligent motor lock device operation manual

The intelligent motor lock is a new type of intelligent lock with a microcomputer control system. And has the copyright of independent computer software control system. This lock has a number of practical functions, which is most suitable for DIY. You can adjust the parameters at will, so that you can use it conveniently, smoothly, securely, securely and safely.

First, the function

1. The lock has electric control unlocking, manual unlocking, and door closing active locking (time adjustment; in the case of power failure, it can also unlock).

2. This lock is applicable to various doors such as left door, right door, inner door opening and outer door opening.

3, can be used with the building intercom host, access control system, can also be used independently.

4, can be directly used for linkage lock (bank double door lock), GPS satellite to determine the function.

5, with sound and light tips, a variety of operating conditions (sound can be turned off).

6, no access after unlocking, the door will be active lock, and can be adjusted at any time (a total of four time).

7. Lock tongue delay function: After closing the door, the lock tongue has a delay function and can be adjusted at any time.

8. This lock has a door closing alarm function.

9, with remote control unlock, the system determines the function (need to be equipped with remote control).

Second, the specification parameters

1. Operating voltage: DC12V unlock current is less than 300mA, quiescent current is less than 15mA.

2, buzzer: divided into two conditions can be selected (K4) ON, OFF.

3. Active locking function: K2, K3 combination switch can adjust the active locking time to 4, 6, 9, 12 seconds.

4, lock tongue delay: K1 is the lock tongue delay switch, ON pass is 2.5 seconds, OFF is 1.5 seconds.

5, remote control function: plug in the receiving board, press the handle A, B, C any key to open the D key system to determine.

6. Terminal: +12V is connected to DC DC12V+, GND is grounded to OV, L+/L- is connected to DC voltage 6V-12V to unlock signal.

7. J1 is the motor plug, J2 is the magnetic switch plug, and J3 is the GPS to determine the switch plug.

8, J3, 1 GPS output, short-circuit system priority terminal operation program is immediately locked.

2Double-door linkage interlocking function: J3 normally open system operation, J3 normally closed system determination.

9. The lock tongue fits the GA/T 73-945.1.6 Class B specification.

10. The service life is more than 300,000 times.

Third, the application methods and adjustments:

1. According to the terminal block: After connecting four lines, power on the test DC12V DC power supply.

2. Pull the switch K4 to NO, close the door, lock after 1.5 seconds, and the buzzer drops a long sound.

3, L + / L - trigger DC12V voltage unlock: the buzzer drops three lights flashing.

4. After the door delay is not opened, the door will be locked automatically (the delay time is adjustable at 3, 6, 9, 12 seconds).

5. The door will not close within 15 seconds after opening the door, and the buzzer alarm light will flash.

6. The delay of the lock tongue is adjusted to K1, which facilitates the alignment of the lock tongue.

Fourth, the detailed adjustment methods are as follows:

1. Combination switch: K1: for the tongue delay switch ON: 2.5 seconds, OFF: 1.5 seconds; K2, K3 is the active lock time; adjust K4 for the buzzer switch: K4 ON is on, OFF is off; Initially: K1, K2, K3 are OFF, and K4 is ON.

2. J1 is the motor plug, J2 is the magnetic induction switch plug, and J3 is the GPS linkage special plug.

3, the plug is a special remote control socket: (can directly penetrate the remote control receiver board). Note: 1 is DC12V + 2T trigger computer to open the door 3GND ground 4D system to determine the function 5A, B, C are open the door or solve the function.

4, terminal block: +12V DC / GND ground; L + / L - connected to DC 6V-12V voltage, can be directly connected to the L+ / L- of the building intercom host.

Five, note:

1. The normal gap of the door joint is 4-6mm.

2, can not burn electric welding, to avoid demagnetization of small buckle magnet.

3, voltage application range DC12V DC positive and negative 10%

4. Please install the lock body and then install the small buckle. Do not hit the small buckle to avoid the magnet falling.

5, the small buckle as far as possible to the lower device, to avoid the door drooping affect the locking tongue.

Accessories: 1 lock, 3 keys, 2 long screws, 4 short screws, 3 eye plates, one manual